Find Onyx RCR, CTY2, and LZR stuff using the mobile browser “find on page” feature. Search on PC and Mac with the keyboard key combo “Ctrl+F” or or “Command-F”.
Open a ticket with me on the contact page for my assistance in person or remotely for repairs, modifications, or technical support. I can also be reached on Instagram and Facebook.
Onyx RCR BATTERY CHARGE CONNECTOR XLR STOCK
BATTERY CHARGE CONNECTOR XT60 UPGRADE
CHARGE CABLE CONNECTOR PROTECTIVE CAP
BATTERY CHARGE CABLE CONNECTOR ADAPTER
BATTERY DISCHARGE CABLE CONNECTOR QS8
CABLE Phase CONNECTOR SUPRA X
Supra X connectors to replace the phase wire yellow junction box and the phase wire lugs. Four sets are included but only two sets are required. Make sure to match the yellow, blue, and green phase wires to their corresponding color.
Battery Discharge CABLE TERMINAL CONNECTOR
XLR CHARGE CABLE CONNECTOR EXTENSION
Wire color kits 22-18 Awg
Use the "22 awg" color wire kits to install turn signals and other electric accessories. Higher power headlights benefit from "20 awg" wires. Use "18 awg" wires for electrical projects that demand higher power.
PVC cable insulation does not harden and crack over time, is resistant to; corrosion, impact, abrasion, and weathering, is static electricity-proof, and is lower heat resistance compared to Silicone cables.
Silicone insulated cables offer the highest flexibility, high heat resistance, resistance to oils, and solvent, susceptibility to cable damage, and less hard-wearing than PVC Leads. Silicone leads generate static electricity.
Under 70 discharge amps use "8 awg" wire with an SB50 connector for the battery discharge connector cable. Over 70 amps use "8 awg" wire with a QS 8 connector. Over 120 amps use "6 awg" with a QS 8 connector. Over 200 amps convert to double battery connector cables with "8 awg" and QS 8 connector. Over 300 amps use double QS 8 connector with "6 awg" wire.
CABLE and connector SHRINK TUBING
Use 15mm shrink tubing for an XT60 connector, 30mm shrink tubing for a QS8 connector, and 12.7mm shrink tubing for 8awg and 6awg cables. Using 6.4mm and 9.5 for 12-22 awg wires works fine.
The Onyx RCR tire size is 17" by 2.75. The quality, ratings, tread pattern, and manufacturers stated use matter more than anything else. Keep the front and rear tire inflated to 35 psi. The tire size 80/90/17 is the same as 2.75 X 17.
Mounting a 3' tire on the front of the Onyx RCR will require a wider front fork stabilizer. A 3' rear tire does not require any modifications.
HELMET ANTI FOG FILM
HELMET WIND BLOCKER
HEADLIGHT TRIPLE BAR
FLOOD LIGHT MOUNT
TURN SIGNAL FLASHER RELAYS
SIDE PANEL IS 20 INCHES LONG
LED STRIP KIT
THERMAL LONG JOHNS
CAFE RACER HANDLEBAR
TIRE VALVE EXTENSION
TIRE PRESSURE BLUETOOTH MONITORING
When ordering a Quad Lock use the “Build Your Own” page. My Quad Lock setup is the lever, vibration dampener, and bar clamp to center mount on the handlebar. The standard setup is the lever, extension arm, and bar clamp.
ALARM CONNECTOR REQUEST
Send an email with your order number to email@example.com and let them know the controller is for an Onyx RCR so they can provision the controller with the alarm connectors.
PROGRAM CONTROLLER AND PAIR WITH MOTOR
Follow the instructions on the “Onyx Sicko Mode” post to program the controller with an Android device or Windows laptop. You will find the stock Onyx RCR Kelly controller settings at the bottom of the “Onyx Sicko Mode” post. Change the field “Motor Identify En” from 85 to 170, then tap write. Turn off the bike and prop the rear wheel off the ground. When you turn on the bike, it will begin to randomly spin the rear tire on its own for a minute as it pairs the motor to the controller.
KELLY CONTROLLER KLS7230S MANUAL
HALL SENSOR TESTER
HALL SENSOR VIDEOS
Before ordering new rear brake pads, remove your old rear brake pads to visually confirm if they match v1 or v2. If neither v1 nor v2 matches yours, then contact me, I will be glad to assist.
Order two sets of the 16-inch tire iron set for a total of four spoons.